SiC FGD spray nozzles

Short Description:

WET FLUE GAS DESULFURIZATION WITH LIME/LIMESTONE SLURRY  Our products have a long service life, which is similar with famous international brands of SPRAY, BETE, LECHLER. Features Desulphurisation efficiency: above 99% Availability” over 98%  Engineering not dependent on any specific location Marketable product Unlimited part load operation Method with largest number of references in the world Purification of flue gas by lime suspension For the wet desulphurisation of flue gas, it...


  • Port: Weifang or Qingdao
  • New Mohs hardness: 13
  • Main raw material: Silicon Carbide
  • Product Detail

    ZPC - silicon carbide ceramic manufacturer

    Product Tags

    WET FLUE GAS DESULFURIZATION WITH LIME/LIMESTONE SLURRY 

    Our products have a long service life, which is similar with famous international brands of SPRAY, BETE, LECHLER.

    Features

    Desulphurisation efficiency: above 99%
    Availability” over 98% 
    Engineering not dependent on any specific location
    Marketable product
    Unlimited part load operation
    Method with largest number of references in the world

    Purification of flue gas by lime suspension

    For the wet desulphurisation of flue gas, it is passed through an absorber (scrubber). The lime suspension offered in the absorber (limestone or lime milk) reacts with the sulphur dioxide from the flue gas. The better the mass transfer is, the more effective the desulphurisation is.

    Simultaneously with the absorption, the flue gas is saturated with water vapour. The so-called “clean gas” is usually discharged via a wet chimney or cooling tower. The water thus lost for the process must be replaced. The lime slurry pumped in circulation is kept chemically active by repeatedly draining a saturated partial flow and replacing it with new reactive suspension. The drained part flow contains gypsum, which – simplified – is a reaction product of lime and sulphur and can be marketed after dewatering (e.g. for gypsum walls in the construction industry).

    Special ceramic nozzles are used to inject the lime suspension into the absorber. These nozzles form many small droplets from the pumped suspension and thus a correspondingly large reaction surface for good mass transfer. The ceramic material permits long service life despite the fact that lime suspension with gypsum content has abrasive properties. In the design we attach great importance to free cross-sections, so that smaller impurities in the suspension cannot set the nozzles. For economical operation, these nozzles can be adapted to the highest efficiency range of the pump. A nozzle can be specified for (almost) every process engineering challenge. In addition to full-cone and hollow-cone nozzles in various spray angles and flow rates, the ZPC nozzle with patented twist compensation is also available.

    The absorption zone consists of several levels of nozzles and a horizontally installed droplet separator system, in order to return the fine droplets carried along in the gas stream to the process. With our high performance droplet separators you can increase the efficiency of your plant.

    The solids in the suspension can lead to deposits, e.g. in the droplet separator, in the inlet duct or on pipes, which can lead to problems in operation. Since water is always withdrawn from the circuit through evaporation, water must be fed into the absorber, which can and should be used for cleaning. ZPC tongue nozzles have proven themselves for cleaning the flue gas inlet. ZPC full cone nozzles are usually used for cleaning the droplet separators.

    Plastics (e.g. for pipelines) and rubber (e.g. gaskets, rubber linings, etc.) are often used in an absorber whose temperature resistance is lower than the temperature of the uncooled flue gas. Normally, the suspension pumped in a circuit cools the flue gas sufficiently, but if, for example, the feed pump is suspended, the plastics and rubbers could be destroyed. Small special-alloy metal nozzles have proven their worth here, which take over cooling during this time and thus protect the investment of the flue gas desulphurisation plant.

    1 喷嘴和检测 3, DN50 Vortex FGD nozzles DN100 Dual Gas Scrubbing Nozzle DN100 Dual vortex nozzle LKL series DN100 Gas Scrubbing nozzle Gas Scrubbing Nozzle

    Reaction bonded silicon carbide (SiSiC): Moh’s hardness is 9.2, with excellent resistance to erosion and corrosion, excellent abrasion-resistance and anti-oxidation. It is 4 to 5 times stronger than nitride bonded silicon carbide. The service life is 7 to 10 times longer than alumina material. The MOR of RBSiC is 5 to 7 times that of SNBSC, it can be used for more complex shapes.

    Some Products: 

    wear resistant silicon carbide liner, cone liner, pipe, spigot, plates (10) wear resistant silicon carbide liner, cone liner, pipe, spigot, plates (7) 1 Large size cone liner and spigot 1 SiC Burner nozzle

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

     

    Silicon carbide ceramic factory,
    Silicon carbide ceramic manufacturer,
    FGD nozzle,
    120° FGD spary nozzle,
    90° FGD spary nozzle,
    110° FGD spary nozzle,
    Flue gas desulfurization nozzle,
    FGD Absorber slurry spray nozzles,
    LIME LIMESTONE SLURRY FGD nozzles,
    silicon carbide Spray nozzle,
    Silicon carbide radiant tube,
    Hydrocyclone liner,
    silicon carbide cone liner factory,
    silicon carbide pipe liner factory,
    silicon carbide bends,
    silicon carbide apex,
    silicon carbide nozzle factory,
    RBSC liner,
    RBSC burner nozzle factory,
    RBSC Radiant tube,
    Wear resistant ceramic linnings,
    Wear resistant silicon carbide linner,
    Wear resistant silicon carbide pipe,
    silicon carbide inlet,
    silicon carbide elbow,
    silicon carbide TEE pipe,
    Silicon carbide ceramic liner factory,
    silicon carbide tiles,
    Wear resistant ceramic tiles,
    Silicon Carbide Ceramic lined pipe and elbow manufacturer,
    Wear resistant ceramic tiles factory manufacturer,
    wear resistant tiles 150*100*25mm,
    Ceramic lined pipe,
    silicon carbide spigot,
    silicon carbide plate,
    silicon carbide customized products,


  • Previous:
  • Next:

  • Shandong Zhongpeng Special Ceramics Co., Ltd is one of the largest silicon carbide ceramic new material solutions in China.  SiC technical ceramic: Moh’s hardness is 9 (New Moh’s hardness is 13), with excellent resistance to erosion and corrosion, excellent abrasion – resistance and anti-oxidation. SiC product’s service life is 4 to 5 times longer than 92% alumina material. The MOR of RBSiC is 5 to 7 times that of SNBSC, it can be used for more complex shapes. The quotation process is quick, the delivery is as promised and the quality is second to none. We always persist in challenging our goals and give our hearts back to society.

     

    1 SiC ceramic factory 工厂

  • Related Products

    WhatsApp Online Chat !